Prime Iranian polyethylene granules – HDPE, LDPE and LLDPE film, injection, blow moulding and pipe grades – with open datasheets and today’s rate CFR Karachi.
In Pakistan polyethylene granules are usually called plastic dana. Karachi rate lists quote them as HDPE Film, HDPE Injection, HDPE Blow Moulding, LDPE Film and LLDPE Film, and the grades on this page follow the same groups.
Choose your process: HDPE film HDPE injection HDPE blow moulding HDPE pipe LDPE film LLDPE film
HDPE 0035 – Blow Moulding Grade
HDPE 0035 is a high-molecular-weight, highly crystalline blow moulding grade combining good extrusion behaviour with superior mechanical properties.
- MFR 0.35 g/10 min 190 °C / 2.16 kg
- Density 0.959 g/cm³
- Process Blow Moulding
HDPE 5110 – Blown Film Grade
HDPE 5110 is a high-molecular-weight, high density polyethylene with broad molecular weight distribution and 1-hexene comonomer, developed for thin films with excellent strength and rigidity.
- HLMI 10 g/10 min 190 °C / 21.6 kg
- Density 0.951 g/cm³
- Process Blown Film
HDPE 52518 – Injection Moulding Grade
HDPE 52518 is a high-flow HDPE copolymer for injection moulding, offering a good balance between easy processing, flowability and mechanical properties.
- MFR 18 g/10 min 190 °C / 2.16 kg
- Density 0.952 g/cm³
- Process Injection
HDPE 62N07 – Injection Moulding Grade
HDPE 62N07 is an injection moulding grade with good impact strength, easy processing, high rigidity and UV resistance.
- MFR 7 g/10 min 190 °C / 2.16 kg
- Density 0.962 g/cm³
- Process Injection
HDPE BL3 – Blow Moulding Grade
HDPE BL3 is a blow moulding grade with 1-butene comonomer for small containers up to 10 litres.
- MFR 1.2 g/10 min 190 °C / 5 kg
- Density 0.954 g/cm³
- Process Blow Moulding
HDPE EX3 – Pipe Grade (PE80)
HDPE EX3 is a natural high density polyethylene with 1-butene comonomer, classified as PE80.
- MFR 0.45 g/10 min 190 °C / 5 kg
- Density 0.945 g/cm³
- Class PE80
HDPE EX5 – Blown Film Grade
HDPE EX5 is a high-molecular-weight, bimodal high density polyethylene with 1-butene as comonomer.
- MFR 0.28 g/10 min 190 °C / 5 kg
- Density 0.949 g/cm³
- Process Blown Film
HDPE F7000 – Blown Film Grade
HDPE F7000 (7000F) is a high density polyethylene developed for very thin, high-strength films.
- MFR 0.04 g/10 min 190 °C / 2.16 kg
- Density 0.952 g/cm³
- Process Blown Film
HDPE PE100 Natural – Pipe Grade (PE100)
PE100 Natural is a bimodal high density polyethylene pipe resin with 1-butene comonomer.
- MFR 0.22 g/10 min 190 °C / 5 kg
- Density 0.948 – 0.957 g/cm³
- Class PE100
LDPE 2119 – Film Grade
LDPE 2119 is a low density polyethylene with excellent optical properties for general-purpose thin film.
- MFR 1.9 g/10 min 190 °C / 2.16 kg
- Density 0.921 g/cm³
- Process Blown Film
LDPE 2420H – Film Grade
LDPE 2420H is a non-additivated low density polyethylene for blown and cast film.
- MFR 1.9 g/10 min 190 °C / 2.16 kg
- Density 0.924 g/cm³
- Process Blown / Cast Film
LLDPE 209 – Film Grade
LLDPE 209 is a butene-1 LLDPE copolymer with antioxidant for general-purpose film, also suitable for blending with LDPE.
- MFR 0.9 g/10 min 190 °C / 2.16 kg
- Density 0.920 g/cm³
- Process Blown Film
LLDPE 22B02 – Film Grade
LLDPE 22B02 is a linear low density polyethylene with 1-butene comonomer and high stiffness.
- MFR 2.0 g/10 min 190 °C / 2.16 kg
- Density 0.922 g/cm³
- Process Blown / Cast Film
PE100 Black – HDPE Pipe Compound
PE100 Black is a bimodal high density polyethylene pipe compound with 1-butene comonomer and finely dispersed carbon black.
- MFR 0.22 g/10 min 190 °C / 5 kg
- Density 0.957 g/cm³
- MRS 10 MPa
HDPE 3840 (HD3840UA) – Rotational Moulding Grade
HDPE 3840 (HD3840UA) is a UV-stabilised butene copolymer for rotational moulding of tanks and large containers.
- MFR 4 g/10 min 190 °C / 2.16 kg
- Density 0.938 g/cm³
- Process Rotomoulding
HDPE 52B18 – Thin-Wall Injection Grade
HDPE 52B18 is a butene-copolymer HDPE injection grade with easy processing, high rigidity and strength for general purpose and thin-walled containers.
- MFR 15 – 21 g/10 min 190 °C / 2.16 kg
- Density 0.951 – 0.953 g/cm³
- Process Injection
HDPE 54B04 UV – Injection Grade for Crates
HDPE 54B04 is a UV-resistant HDPE injection grade with high rigidity and easy processing for crates, pallets, seats and boxes.
- MFR 3.2 – 4.8 g/10 min 190 °C / 2.16 kg
- Density 0.950 – 0.958 g/cm³
- Additive UV
HDPE 5510 (HBM5510) – Large Blow Moulding Grade
HDPE 5510 (HBM5510) is a hexene-copolymer HDPE for large blow-moulded parts such as jerry cans and open-top drums, with high stiffness and good ESCR.
- HLMI 10 g/10 min 190 °C / 21.6 kg
- Density 0.955 g/cm³
- ESCR 90 h
HDPE 60507 UV – Injection Moulding Grade
HDPE 60507 (HD-60507/UV) is a gas-phase HDPE homopolymer injection grade with good flow and high stiffness for crates and general purpose parts.
- MFR 7.5 g/10 min
- Density 0.958 g/cm³
- Additive UV
HDPE HI500 (HI0500) – Injection Moulding Grade
HDPE HI500 (HI0500) is a natural HDPE injection grade that combines high stiffness with good physical properties for crates and thick-wall parts.
- MFR 4 – 6 g/10 min 190 °C / 2.16 kg
- Density 0.963 – 0.967 g/cm³
- Process Injection
LDPE 0075 (LH0075) – Heavy-Duty Film Grade
LDPE 0075 (LH0075) is a low-MFR, high molecular weight LDPE for heavy-duty film, with strong dart impact, good yield strength and high stiffness.
- MFR 0.75 g/10 min 190 °C / 2.16 kg
- Density 0.920 g/cm³
- Process Heavy-duty film
LDPE 0190 (LF0190) – Film Grade
LDPE 0190 (LF0190) is an additive-free, high molecular weight LDPE for general purpose and lamination film, with high output and good drawdown.
- MFR 1.9 g/10 min 190 °C / 2.16 kg
- Density 0.921 g/cm³
- Additives None
LDPE 020 (LF0200) – Film Grade
LDPE 020 (LF0200) is a high molecular weight low density polyethylene film grade with good extrusion behaviour, high dart impact and high stiffness.
- MFR 2 g/10 min 190 °C / 2.16 kg
- Density 0.920 g/cm³
- Process Blown film
LDPE 1922 (1922T) – Injection Moulding Grade
LDPE 1922 (1922T) is a high-flow low density polyethylene injection grade with a good balance of flow and mechanical properties for toys, housewares and snap-on lids.
- MFR 22 g/10 min 190 °C / 2.16 kg
- Density 0.919 g/cm³
- Process Injection
LDPE 2100 (2100TN00) – Heavy-Duty Film Grade
LDPE 2100 (2100TN00) is a low-MFR (0.3) low density polyethylene for heavy-duty film such as shrink hoods, industrial sacks and liners.
- MFR 0.30 g/10 min 190 °C / 2.16 kg
- Density 0.921 g/cm³
- Process Heavy-duty film
LDPE 2102TX – General Purpose Film Grade
LDPE 2102TX (2102TX00) is a general purpose low density polyethylene film grade for a wide range of film widths and thicknesses.
- MFR 1.9 g/10 min 190 °C / 2.16 kg
- Density 0.921 g/cm³
- Process Blown film
LDPE 2420E02 – Clear Film Grade
LDPE 2420E02 is a high-clarity, additive-free low density polyethylene for food packaging, lamination and fine shrink film.
- MFR 1.95 g/10 min 190 °C / 2.16 kg
- Density 0.9235 g/cm³
- Additives None
Polyethylene granules from Iran – buyer’s guide for Pakistan
Pakistan does not produce polyethylene, so every tonne of HDPE, LDPE and LLDPE used by its converters is imported. Iranian polyethylene is one of the closest sources: containers from Bandar Abbas reach Karachi or Port Qasim in a few days and trucks can cross at Taftan. Rabin Polymer supplies prime grades from Iranian producers with an open specification table and a one-page datasheet for each grade.
Choose by process
| Process / Karachi label | Grades | Typical products |
|---|---|---|
| HDPE Film | EX5, 5110, F7000 | Shopper, T-shirt and garbage bags, thin film |
| HDPE Injection | 62N07, 52518 | Crates, pallets, buckets, caps |
| HDPE Blow Moulding | BL3, 0035 | Bottles, jerrycans, drums |
| HDPE pipe resin | PE100 black, PE100 natural, EX3 | Water and gas pipe, ducts |
| LDPE Film | 2420H, 2119 | Shrink film, lamination, clear bags |
| LLDPE Film | 209, 22B02 | Agricultural film, liners, FFS sacks |
HDPE, LDPE or LLDPE?
HDPE (density about 0.94–0.96 g/cm³) is stiff and strong – the choice for thin bags, rigid injection and blow-moulded parts and pressure pipe. LDPE (about 0.92 g/cm³) is soft, clear and easy to seal – ideal for shrink and lamination film. LLDPE (about 0.92 g/cm³) combines low density with much higher toughness and is usually blended with LDPE for strong film.
Reading a polyethylene datasheet
- Melt flow rate (MFR/MFI): low values (below 1) mean high molecular weight – strong film and pipe; high values mean easy flow for injection moulding.
- Density: higher density means higher stiffness and lower clarity.
- Test conditions: always compare MFR at the same temperature and load (for example 190 °C / 2.16 kg).
Market overview
Polyethylene imports into Pakistan are dominated by film grades, followed by injection, blow moulding and pipe grades. Karachi is the main trading hub, with converters spread across Karachi, Lahore, Faisalabad, Gujranwala and Peshawar. Rates move with regional polyethylene prices, freight and the rupee, which is why many buyers follow a weekly rate list before they book.
What to check before you buy
- The exact grade code and producer printed on the bag.
- MFR and density on the lot certificate – they must match the datasheet.
- Packing: original 25 kg producer bags on pallets, dry and undamaged.
- Shipping documents that match the goods: invoice, packing list and certificate of origin.
Grade notes
HDPE EX5 – HDPE EX5 is a high-molecular-weight, bimodal high density polyethylene with 1-butene as comonomer. It combines good stiffness and tenacity with a low gel level, producing strong blown films with a paper-like feel for bags and wrapping. Key strengths: high molar mass film grade, good stiffness & tenacity, low gel level. In Pakistan it is used for T-shirt carrier bags, shopping bags and thin, paper-like HDPE film.
HDPE 62N07 – HDPE 62N07 is an injection moulding grade with good impact strength, easy processing, high rigidity and UV resistance. It is especially suitable for crates, pallets, boxes, seats and heavy-duty housewares. Key strengths: high rigidity, good impact strength, uv resistant. In Pakistan it is used for fruit and vegetable crates, bottle crates, pallets and buckets.
HDPE BL3 – HDPE BL3 is a blow moulding grade with 1-butene comonomer. High rigidity and an excellent balance of stiffness and environmental stress-crack resistance make it ideal for detergent and medicine bottles and all bottles and small containers below 5 litres. Key strengths: high density & stiffness, good flow & impact strength, good stress-crack resistance. In Pakistan it is used for detergent, shampoo, edible-oil and medicine bottles up to 5 litres.
PE100 Black – PE100 Black is a bimodal high density polyethylene pipe compound with 1-butene comonomer and finely dispersed carbon black. It delivers top-quality PE100 pressure pipes for water and gas at higher pressures or thinner walls than PE80, with long-term UV protection. Key strengths: pe100 black compound, excellent slow-crack-growth resistance, uv protected. In Pakistan it is used for water mains, gas distribution pipe and pressure ducts for utility projects.
LDPE 2420H – LDPE 2420H is a non-additivated low density polyethylene for blown and cast film. It offers good heat sealing, good optical properties and easy processing for medium-gauge films of 70 – 220 µm: packaging film, bags, pouches and shrink film. Not intended for medical applications. Key strengths: good heat seal, high clarity & gloss, good processability. In Pakistan it is used for shrink film, heavy-duty bags, lamination and medium-gauge packaging film.
LLDPE 209 – LLDPE 209 is a butene-1 LLDPE copolymer with antioxidant for general-purpose film, also suitable for blending with LDPE. Compared with conventional LDPE it gives better sealing, higher puncture resistance, greater draw-down and higher tensile strength. Food-contact grade. Key strengths: better sealing, high puncture resistance, greater draw-down. In Pakistan it is used for agricultural film, liners, FFS sacks and LDPE/LLDPE blends for stronger film.
Supply to Pakistan
We ship polyethylene granules from Iran in 25 kg bags on pallets (jumbo bags on request). Sea freight goes in 20′ and 40′ containers from Bandar Abbas to Karachi or Port Qasim; inland buyers can also receive trucks via Taftan. The shipping mode, route and Incoterm are agreed for each order, depending on quantity, destination and timing. Every shipment travels with a commercial invoice, packing list, certificate of origin and the producer datasheet.
Need a rate? Send the grade, quantity and city on WhatsApp or use the enquiry form – we reply within one business day. You can also join our free weekly rate list for Pakistan.
Frequently asked questions
Is Iranian polyethylene prime or recycled?
All grades on this site are prime, virgin polyethylene produced by Iranian petrochemical plants and supplied in the producer’s original bags.
How are rates quoted for Pakistan?
We quote per tonne for the agreed Incoterm – for example CFR Karachi / Port Qasim by sea or delivered by truck via Taftan – based on the weekly market.
Can I mix grades in one container?
Yes, mixed loads of two or three grades are possible; tell us the tonnage of each grade when you enquire.
Where can I see all datasheets?
All PDFs are listed on our Technical Datasheets page.
